Single Sided Mini Clamps - Chrome & Satin

Single Sided Mini Clamps - Chrome & Satin

Single sided mini clamps used to attach our cable display pockets to our floor to ceiling cable kits. The small clamps support pockets made from up to 2.5mm thick acrylic, the large clamps up to 4.5mm. GTM Cable pocket sizes A5, A4 & A3 are produced from 2mm thick acrylic. Our A2 & A1 pockets are produced from 3mm thick acrylic.

Inventory

Click links above to see quantity discounts!

Save wishlist

Calculating the number of cable kits required:

Whether you're assembling one of our cable display kits in your shop window or mounting it to the wall, the simple rule applies whereby both side/end cables within the display will use single sided clamps only.

Regardless of how many columns wide your display is there will always be two side/end cables.

Example: Any display layout that is 5 columns wide which contains single, double, or triple pockets within each column, will always require 6 cables, since the fence panel vs fence post rule applies. Out of the 6 cables naturally you'll have 2 at the side/end, and therefore that obviously leaves 4 in the centre/middle.

We generally consider any cable that isn't a side/end cable to be a middle cable.

Clamp to pocket and pocket to cable assembly procedure:

  1. Each clamp contains two jaws or slots as they're sometimes referred to, each of which has a small grub screw that performs the clamping action when gently tightened up to grip the cable/wire or flange of the poster/cable pocket.
  2. To attach a clamp to the pocket flange you simply loosen the screw just enough to allow the flange to insert into the jaw, and then you just tighten the screw gently.
  3. After all four clamps have been attached, remove the end screw from the narrower slot of each clamp. The next stage is to position the pocket between the cables where it will be suspended. Finally, you simply put the screws back in and tighten a couple of turns, adjust the height of the pocket as desired, and then tighten the screw just a little more to grip the cable.

If you're constructing a display which uses 3 cables or more, then a slightly different approach is required (Please refer to our double clamp parent product description for details).

No recommended products at the moment.
 
Single Width Acrylic Cable Pockets - Portrait
View

Acrylic portrait pockets used in our cable display systems and wall mounted frame displays. You can either insert one piece of paper/card printed on one or both sides, or you can insert two pieces back to back, since the pockets can be seen through equally well from both sides. 

click to see more

 
 
Single Width Acrylic Cable Pockets - Landscape
View

Our single landscape acrylic poster pockets can also be seen through equally well from both sides, just like our portrait pockets. You can also suspend landscape and portrait single pockets between the same two cables, providing the portrait size is the next larger "A" size. 

click to see more

 
 
Double Width Cable Display Pockets - Portrait
View

These double width acrylic poster pockets are used in the exact same way as our single pockets. However, our double cable pockets are approximately twice the width which allows your advertisements to be inserted into the separate sleeves side by side.

click to see more

 
 
Double Sided Mini Clamps - Chrome & Satin
View

Double sided mini clamps used to attach our cable display pockets to our floor to ceiling cable kits. The small clamps support pockets made from up to 2.5mm thick acrylic, the large clamps up to 4.5mm. GTM Cable pocket sizes A5, A4 & A3 are produced from 2mm thick acrylic. Our A2 & A1 pockets are produced from 3mm thick acrylic.

click to see more

 
 
Floor To Ceiling Cable Kits - Chrome & Satin Finish
View

Cable display kits supplied complete with the top and bottom fixings. Initial cable length 4 metres designed to be cut shorter as required. Optional wall mounted fittings available. select your preferred finish, either shiny chrome or satin plate.

click to see more